Browse docs

Play Orfeo Through Your Own Sounds

New
4 min read
0:004:02

Orfeo has three sound engines of its own, but it can also play through sounds you already have: a digital piano, a sound module or synth on your desk, or the software instruments in your music software (VST3, Audio Unit or CLAP plugins).

Orfeo sends the song, and the notes you play, out as MIDI, and your instrument plays them with its own sounds. Everything else in Orfeo works as usual: the piano roll, the keyboard, looping, the tempo and the Explorers.

Before you start

  • This works with the GM sound engine. Studio and Native always play inside Orfeo. See Audio and Sound Engines.
  • You choose where GM goes in Settings › MIDI Keyboard › Sound & Latency › General MIDI sound. Orfeo’s built-in synth is the usual choice; every MIDI output on your computer is listed below it.

A digital piano, sound module or hardware synth

  • Connect the instrument to your computer (USB, or a MIDI interface) and switch it on.
  • In Orfeo, open Settings › Audio and choose GM.
  • Open Settings › MIDI Keyboard › Sound & Latency and, under General MIDI sound, pick your instrument.
  • Press play.

Choose an instrument that makes its own sound. A keyboard controller without speakers or sounds of its own plays nothing.

Software instruments (VST3, Audio Unit, CLAP)

Your plugins run in a host: a music program such as a DAW (Ableton Live, Cubase, Logic, Reaper, Bitwig…) or a small free host like Carla. Orfeo reaches the host through a virtual MIDI cable, a MIDI port that exists only inside your computer.

1. Make a virtual MIDI cable

  • Windows: install loopMIDI (free), start it, and click + to add a port. Leave loopMIDI running.
  • macOS: open Audio MIDI Setup (in Applications › Utilities), choose Window › Show MIDI Studio, double-click IAC Driver, and tick Device is online.
  • Linux: run sudo modprobe snd-virmidi in a terminal. It adds Virtual Raw MIDI ports until the next restart. Or use a host such as Carla, which makes its own MIDI input that Orfeo can see.

2. Set up your host

  • Open your host and load the instrument you want to hear.
  • Set the instrument track’s MIDI input to the virtual port.
  • Turn on input monitoring (or arm the track), so it plays whatever arrives.
  • To hear the whole song through one instrument, let it listen to all channels.

3. Point Orfeo at it

  • In Orfeo, open Settings › Audio and choose GM.
  • Open Settings › MIDI Keyboard › Sound & Latency and, under General MIDI sound, pick the virtual port.
  • Press play. The song now sounds through your instrument.

If you start Orfeo before the virtual cable or the host, the port may not be listed yet. Open the setting again once they are running.

Which part goes where

Every track keeps its own MIDI channel, so a host can give each part its own instrument.

What

MIDI channel

The song’s tracks

As written in the file, drums on channel 10

Notes you click on the on-screen keyboard and in the Explorers

15

Notes you play on a connected MIDI keyboard

16

  • One instrument for everything: set it to listen to all channels (often called omni).
  • A separate sound for each part: in your host, route each channel to its own instrument. Drums on channel 10 usually want a drum kit.

Good to know

  • The song’s own settings go along. Each track’s instrument choice, volume and pan go out as written in the file. Many plugins follow them; some ignore instrument changes and always play their own sound.
  • Mute and solo work as usual: a muted track sends nothing.
  • Orfeo’s volume sends standard volume messages. If your instrument ignores them, set the level in the host instead.
  • The metronome and count-in stay in Orfeo and play through your computer’s sound.
  • Export to audio always uses Orfeo’s own sounds (Studio or Native), not your instrument.
  • A little late? Some instruments and hosts add a delay. Line the picture up with what you hear in Settings › MIDI Keyboard › Sound & Latency › Audio delay offset.

Going back

Under General MIDI sound, choose Orfeo’s built-in synth again. If the instrument you chose is unplugged or the host is closed, Orfeo says so and plays its own synth until it is back.

Wondering whether Orfeo can load plugins itself, or work with your DAW in other ways? See Orfeo and Plugins.